KDWVC-700(WiFi)

數據采集器恢複出廠設置

Reset Modem operation

1、如圖1，将設備按要求連接好WIFI天線（左）和433天線（右），将電源線插好并接通電源，确保電源燈指示燈為紅色顯示，Ready指示燈為綠色狀态。

As shown in Figure 1, connect the device to the WIFI antenna (left) and 433 antenna (right) as required, plug the power cord and turn on the power, make sure that the power light indicator is red and the Ready indicator is green.

2、如圖2,按下RST按鈕5秒鐘。釋放按鈕後，再次快速按Rst按鈕，直到“就緒”指示燈熄滅;

As shown in Figure 2, press the RST button for 5 seconds. After releasing the button, quickly press the Rst button again until the "Ready" indicator goes out;

3、當完成以上操作後，Modem恢複為初始化狀态。并且Ready燈将重新變會綠色狀态。如圖3;

When the above operations are completed, the modem returns to the initial state. And the Ready light will turn green again. As shown in Figure 3

數據采集器與無線路由器配網設置

Network configuration of Modem and wireless router

1、将手機的無線網絡設置為HF-A11x_AP，如下圖

Set the mobile phone's wireless network to HF-A11x_AP, as shown below

2、網絡切換完成，打開手機浏覽器并在地址欄中填入10.10.100.254後點擊确認，如圖所示

After the network switch is completed, open the mobile phone browser and fill in 10.10.100.254 in the address bar and click OK. as the picture shows

*Remarks:

User name: admin

Password: admin

3、進入管理頁面後，點擊右上角的語言，将它更換為英文系統，如圖所示

After entering the management page, click the language in the upper right corner and replace it with the English system。as the picture shows

4、将通訊模塊更改為“Station”模式後點擊确定，如圖所示

Change the communication module to "Station mode", click "Apply" as shown

點擊确認過後，界面将變成下圖，請不要點擊重啟鍊接

After clicking "Apply", the interface will change to the following picture, please do not click the restart link.

5、選擇“無線終端設置”菜單，在右方的選項中點擊“查找”按鍵。如圖

Select the " STA Interface Setting " menu and click the " Search.." button in the options on the right. as the picture shows

選中你的無線信号，點擊“确認”，如圖

Select your Wi-Fi SSID signal and click "Apply", as shown

(*If your signal source is not displayed, click "Refresh" until your signal source appears in the list)

将Wi-Fi 密碼輸入到如下圖的位置中，并點擊确認。如圖所示

Enter the Wi-Fi password into the location as shown in the figure below, and click “Apply”. as the picture shows

6、選擇“串口及其他設置”菜單，修改網絡參數設置裡的三個項目。如圖

 Select the "Application Setting" menu to modify the three items in the “Network Settings”. As shown

更改以下三個項目，參數如下圖

Change the following three items, the parameters are as follows

Mode:Client

Port:1234

Server Address:47.115.28.119

7、選擇“模塊管理”點擊右方的重啟模塊按鍵。采集器将會自動完成配網。如圖

Select "Device Management" and click the “Restart” module button on the right. The collector will automatically complete the network configuration. As shown

點擊重啟按鍵後，Modem上的Ready指示燈将會熄滅，模塊将會進行自動配網。如下圖

After clicking the restart button, the "Ready light" on the Modem will go out and the module will automatically configure the network. As shown below

8、完成以上步驟後，采集将自動重啟自動完成配網工作。當“Ready light & Link light"亮起綠燈時，表示配網成功，采集器已經能正常連接上無線路由器。并且手機上的HF-A11x_AP信号将不會出現。如下圖

After completing the above steps, the collection will automatically restart to complete the network configuration automatically. When "Ready light & Link light" lights up in green, it means that the network configuration is successful and the collector can be connected to the wireless router normally. And the HF-A11x_AP signal on the phone will not appear. As shown below

Ready Light & Link Light will turn on

So far we will complete the initialization of the modem and the distribution network. Next, we will build the power station in the mobile application, and then add the inverter to it for monitoring